Guide · Homeowners · 3 min read · Updated 17 November 2026
Cavity Drain Membrane vs Tanking: Which Is Better for a Basement?
Short answer
A cavity drain membrane is usually the better choice for old UK cellars because it collects water and drains it away instead of trying to hold it back, and it copes with building movement. Tanking bonds to the wall to block water and suits sound walls with low water pressure. For habitable rooms, BS 8102 recommends considering combined protection, so many specialists use both.
How each system works
Tanking is a Type A barrier system under BS 8102. A cement-based slurry, often with waterproofing additives, is brushed or sprayed onto prepared masonry in several coats, with angle fillets formed where walls meet the floor. It bonds to the wall and resists water pressure from outside. Because it is rigid, any crack in the wall behind can crack the coating and let water through.
A cavity drain membrane is a Type C drained system. A studded high-density polyethylene sheet is fixed to walls and laid over the floor, creating a small air gap against the masonry. Water that comes through the wall runs down behind the membrane into a perimeter channel, which carries it to a sump pump or a gravity outlet. The water still enters the structure, but it never reaches the room.
Side-by-side comparison
The table sets out the practical differences homeowners usually ask about. Prices are guide figures for supply and fitting.
| Factor | Cavity drain membrane | Cementitious tanking |
|---|---|---|
| BS 8102 type | Type C, drained | Type A, barrier |
| Guide price | £90–£160 per m² | £70–£130 per m² |
| Wall preparation | Light; tolerates salts and unevenness | Heavy; needs sound, clean substrate |
| Copes with movement | Yes, membrane is flexible | Poorly; cracks can leak |
| Needs drainage or pump | Yes | No |
| Maintenance | Annual sump and channel service | Little, but repairs are harder |
| Fixing shelves later | Into battens or boards | Holes must be resealed |
When tanking is the right choice
Tanking works well on sound, relatively modern masonry or concrete where water pressure is low and there is no space or route for drainage. It suits small areas, such as a single damp wall, a lift pit or a below-ground store, and situations where a sump would be impractical. It also avoids running costs, since there are no pumps to service.
The catch is preparation. Old paint, bitumen, gypsum plaster and salts must be removed back to clean masonry, and the wall needs to be structurally stable. If the building moves seasonally, as many Victorian terraces on clay do, hairline cracks can open through the coating.
- Sound brick, block or concrete walls
- Low or occasional water pressure
- No practical drainage route for a membrane
- Small or isolated areas rather than whole basements
When a cavity drain membrane is the right choice
Membranes are the default for most cellar conversions in older homes. They handle rubble stone, crumbling brick, efflorescence and walls that will never dry out, because they do not depend on bonding to the masonry. They also cope with moderate water pressure and some building movement, and the inspection ports let the drainage be flushed and checked for life.
The commitment is maintenance. If a pump is used, it must be serviced every year, and the system should have twin pumps, a high-level alarm and battery backup so a power cut or pump failure does not flood the room.
What usually goes wrong with each system
Tanking failures nearly always trace back to preparation or movement. Slurry applied over gypsum plaster, old paint or salt-laden render loses its bond and blows off in patches. Missing angle fillets leave the wall-to-floor joint vulnerable, and a single hairline crack from seasonal movement can become a steady weep. Because the coating is hidden under plaster, the leak may only show as staining or blown paint some time later.
Membrane failures are usually about drainage and detailing. Channels clogged with free lime, pumps that were never serviced and outlets blocked outside all let water back up behind the boards. Poorly sealed joints, unplugged fixing holes and pipes passing through the membrane without proper seals are the other common faults. All of these are avoidable with good workmanship and annual maintenance.
- Tanking: poor surface preparation, no fillets, cracking from movement
- Membrane: blocked channels, unserviced pumps, badly sealed joints and pipe entries
Cost over the life of the room
Comparing only the installation price can mislead. Tanking has no running costs but is harder and more disruptive to repair, because finishes must be stripped to find and fix a leak. A membrane system carries an annual sump service from around £150 and eventual pump replacement, but faults are usually found and fixed through the inspection ports without touching the walls.
Over a long ownership, either can work out well. What matters most is matching the system to the wall condition and water risk, then looking after it. Ask each quoting firm what maintenance their design needs, how often, and roughly what it costs each year, so you compare the full picture rather than the headline figure.
Combined systems for habitable rooms
For bedrooms, offices and other Grade 3 spaces, BS 8102 encourages designers to consider combined protection where the consequences of failure are serious. A common approach is to apply a tanking slurry to the lower wall and floor junction or to particular problem areas, then install a membrane over the whole room. If one layer is compromised, the other still protects the finishes.
A survey should decide which approach suits your cellar. Ask the specialist to explain the type, the grade it achieves and how water will be managed if something goes wrong. We arrange this through vetted local waterproofing specialists, with one fixed written price.
Questions people also ask
Can a cavity drain membrane go over old tanking?
Often, yes. Failed tanking can sometimes stay in place if it is stable, with a membrane fitted over it to collect any water that gets through. Loose or hollow sections are usually removed first, and the wall cleaned of fungal growth. Your surveyor will decide based on the condition of the existing coating.
Does tanking need a sump pump?
No. Tanking holds water back rather than collecting it, so there is nothing to pump. That is one of its advantages where drainage is impossible. The trade-off is that the wall behind must be sound and stable, because the coating relies on its bond with the masonry to resist water pressure.
Which system adds more value when selling?
Either can support a sale if it is designed to BS 8102 and properly documented. Buyers and surveyors look for a clear specification, drawings, service records for any pump, and any guarantee or warranty provided. A dry, well-finished room with paperwork matters more than which system sits behind the boards.
Written and checked by the Basement Waterproofing team. Read our editorial policy.
More guides
How Much Does Basement Waterproofing Cost in the UK?
Most UK basement waterproofing costs £90–£160 per m² for a cavity drain membrane or £70–£130 per m² for cementitious tanking. A sump pump system adds…
BS 8102 Explained: Basement Waterproofing Types and Grades
BS 8102:2022 is the British Standard code of practice for protecting below-ground structures from groundwater. It sets three types of protection:…
Converting a Cellar into a Habitable Room: What's Involved
Converting a cellar into a habitable room means waterproofing it to BS 8102 Grade 3, then insulating, ventilating, wiring and finishing it to…
Basement Sump Pump Maintenance: A Practical Guide
A basement sump pump should be professionally serviced once a year, from around £150. The engineer tests both pumps and the high-level alarm, cleans…
Get a free basement waterproofing quote
Tell us what you need and we'll come back with a clear price.
Request a quote